Oct 27, 2026 Leave a message

Hydraulic Pump Types Explained: Manual, Foot And Air-Hydraulic Pumps For Workshop Tools

Hydraulic pumps are used throughout professional automotive and mechanical workshops to power tools that need high, controlled force.

Typical applications include:

Hydraulic pullers

Bearing separators

Hub pullers

Hydraulic nut splitters

Hydraulic cylinders

Workshop presses

Spring compressors

Flange spreaders

Cutting and pushing tools

At first glance, choosing a pump appears simple.

A workshop may ask:

Do I need a hand pump, foot pump or air-hydraulic pump?

But these terms do not always describe the same engineering category.

A manual hand pump describes both the power source and the operating method.

A manual foot pump still uses human force, but the technician operates it with a foot rather than a hand.

An air-hydraulic foot pump, however, uses compressed air as the real power source while the foot pedal controls operation.

This distinction matters because the correct pump should not be selected only by how it looks or how the technician activates it.

The professional selection process should be:

Tool Requirement → Single- or Double-Acting System → Required Pressure → Required Oil Volume → Duty Cycle → Available Power Source → Control Method → Hose and Coupler Compatibility

The most useful rule is:

Choose a hydraulic pump by the hydraulic tool it must power first, then choose the operating method that best suits the workshop.


Quick Answer: What Are the Main Hydraulic Pump Types for Workshop Tools?

For portable workshop tools, the most common pump configurations are:

Manual Hand Pump

Uses a hand-operated lever to move hydraulic oil.

Best suited for:

Portable repairs

Occasional use

Controlled slow movement

Lower-duty-cycle applications

Workshops without compressed air or electricity

Manual Foot Pump

Uses human foot pressure instead of hand force.

Best suited when:

Hands need to remain free

The technician needs to position a tool while pumping

Portability is still important

Air-Hydraulic Pump

Uses compressed workshop air to generate hydraulic pressure.

It may be controlled by:

Foot pedal

Treadle

Pendant

Valve

Best suited for:

Frequent workshop use

Higher cycling

Reduced technician fatigue

Repetitive hydraulic tool operation

The important distinction is:

Hand / Foot = How the technician controls the pump

while:

Manual / Air / Electric / Battery = Where the energy comes from


What Does a Hydraulic Pump Actually Do?

A hydraulic pump moves hydraulic fluid through a closed hydraulic circuit.

The pump creates fluid flow.

Resistance to that flow creates pressure.

That pressure acts on the piston area inside a hydraulic cylinder.

In simplified form:

Hydraulic Pressure × Cylinder Piston Area = Output Force

This means the pump itself does not directly determine whether a system produces:

5 tons

10 tons

or:

20 tons

The cylinder piston area also matters.

A pump rated to a specific pressure can operate different compatible cylinders that produce different forces.

This is why:

Pump pressure and cylinder tonnage are related, but they are not the same specification.


Why 10,000 PSI / 700 Bar Is Common in Portable Hydraulic Tools

Many professional high-pressure workshop systems are designed around approximately:

10,000 PSI

or:

700 bar

This pressure level is widely used for portable hydraulic:

Cylinders

Pullers

Nut splitters

Pressing tools

Spreaders

However, 10,000 PSI should not be treated as a universal requirement.

Some tools operate at lower pressure.

Specialized systems may operate at higher pressure.

The pump, hose, fittings, couplers and tool must all be designed for the same working-pressure range.

Never connect a higher-pressure pump to a lower-rated component simply because the coupler physically fits.


Type 1: Manual Hydraulic Hand Pumps

A hydraulic hand pump uses a lever operated by the technician.

Each stroke moves hydraulic oil from the reservoir into the hydraulic circuit.

The basic process is:

Move Handle

↓

Pump Draws Oil From Reservoir

↓

Oil Moves Through Check Valve

↓

Pressure Builds in Hydraulic Line

↓

Cylinder Extends

This is one of the simplest portable hydraulic power sources.


Why Manual Hand Pumps Are So Common

Their main advantage is independence.

They do not require:

Compressed air

Electricity

Battery charging

Engine power

The technician only needs:

Pump + Hose + Compatible Hydraulic Tool

This makes manual pumps useful for:

Automotive workshops

Mobile mechanics

Fleet service

Field maintenance

Emergency repair

Occasional hydraulic work


Advantages of Manual Hydraulic Pumps

High Portability

Manual pumps are generally compact and easy to transport.

This is useful when the hydraulic tool needs to move between vehicles or workstations.


Good Pressure Control

The technician controls pressure stroke by stroke.

This makes manual pumps useful when slow, progressive force is desirable.

Typical examples include:

Bearing separation

Puller operation

Nut splitting

Controlled pressing


No External Power Source

A manual pump can operate almost anywhere.

That makes it valuable for field work.


Simple Construction

Compared with air or electric pumps, there are fewer powered components.

This can simplify:

Maintenance

Troubleshooting

Storage


Limitations of Manual Hand Pumps

The main disadvantage is operator effort.

If the cylinder requires a large volume of oil, the technician may need many pump strokes.

Repeated high-pressure work can therefore become:

Slow

Physically tiring

Inefficient in high-volume workshops

This becomes especially important when the tool is used several times per day.


Single-Speed vs Two-Speed Hand Pumps

Not all manual pumps operate the same way.

A single-speed pump provides one oil displacement rate.

A two-speed pump typically provides:

High Flow at Low Pressure

for rapid tool movement before load is reached,

then switches to:

Lower Flow at High Pressure

when the tool starts doing heavy work.

This can greatly improve workshop efficiency.

Instead of slowly pumping the cylinder through its entire stroke at the high-pressure flow rate, the technician can move the cylinder toward the workpiece more quickly and then apply force more precisely.


When Is a Two-Speed Pump Better?

A two-speed pump is particularly useful when:

Cylinder stroke is relatively long

Tool must travel before contacting the workpiece

High pressure is required only at the end of the operation

Typical examples include:

Hydraulic pullers

Pressing tools

Bearing separators

Larger cylinders


Type 2: Manual Hydraulic Foot Pumps

A manual foot pump operates using human power just like a hand pump.

The difference is the control method.

Instead of moving a lever by hand:

Technician Uses Foot

↓

Pedal Operates Pump

↓

Hydraulic Pressure Builds

This can provide one major workshop advantage:

The technician's hands remain available to position or monitor the tool.


Why Hands-Free Operation Matters

Consider a hydraulic puller or pressing operation.

The technician may need to:

Hold an adapter

Check alignment

Support a component

Watch the workpiece

Control another fixture

With a hand pump, one hand may be occupied operating the pump.

A foot-operated system can improve ergonomics.


Is Every Foot Pump Air-Hydraulic?

No.

This is one of the most important distinctions in this article.

There are:

Manual Hydraulic Foot Pumps

The technician's foot directly provides the pumping energy.

and:

Air-Hydraulic Foot Pumps

Compressed air provides the energy.

The technician's foot only controls the pedal.

Therefore:

"Foot pump" describes an interface, not necessarily the power source.


Type 3: Air-Hydraulic Pumps

An air-hydraulic pump-also called an air-over-hydraulic pump-uses compressed air to power the hydraulic pumping mechanism.

The process is:

Workshop Compressed Air

↓

Air Motor / Pneumatic Mechanism

↓

Hydraulic Pump

↓

High-Pressure Hydraulic Oil

↓

Cylinder / Tool

This allows relatively low-pressure shop air to power a high-pressure hydraulic circuit.


Why Air-Hydraulic Pumps Are Popular in Workshops

Many automotive workshops already have compressed-air infrastructure.

The same air system may power:

Impact wrenches

Air ratchets

Tire equipment

Pneumatic tools

An air-hydraulic pump can use that existing power source.

This makes it particularly suitable for stationary professional workshops.


Advantages of Air-Hydraulic Pumps

Reduced Technician Effort

The technician does not need to repeatedly operate a long hand lever.

Compressed air provides the pumping energy.


Faster Repetitive Operation

For frequent hydraulic work, an air pump can improve cycle efficiency.

This matters in:

High-volume repair shops

Fleet workshops

Bearing service

Repetitive pressing work


Foot-Controlled Operation

Many air-hydraulic pumps use a treadle or foot pedal.

This leaves both hands free.


Good Match for Professional Workshop Infrastructure

If the shop already has a suitable compressed-air supply, integrating an air pump can be straightforward.


Limitations of Air-Hydraulic Pumps

They require compressed air.

Therefore they are less suitable for:

Remote repairs

Field work without compressor access

Small workshops without sufficient air supply

They also introduce additional components such as:

Pneumatic inlet

Air motor

Exhaust

Additional valves

This increases system complexity compared with a simple manual hand pump.


Manual Hand Pump vs Manual Foot Pump vs Air-Hydraulic Pump

Factor Hand Pump Manual Foot Pump Air-Hydraulic Pump
Main energy source Human Human Compressed air
Operator control Hand lever Foot pedal Foot pedal / valve / pendant
External power needed No No Yes
Portability Excellent Excellent Moderate
Hands-free operation No Yes Often yes
Operator fatigue Highest Moderate Lowest
Repetitive workshop use Moderate Moderate Excellent
Field service Excellent Excellent Limited by air supply
System complexity Low Low Higher
Typical duty cycle Low to moderate Low to moderate Moderate to high

The correct choice depends on workshop conditions rather than pressure alone.


Manual vs Air-Hydraulic: Which Is Better?

Neither is universally better.

A manual pump is usually better when:

Portability is important

Hydraulic work is occasional

There is no compressed air

Simple maintenance is preferred

An air-hydraulic pump is often better when:

Hydraulic tools are used frequently

Workshop air is always available

Technician fatigue matters

Repetitive operation is common

A useful rule is:

Low-frequency + mobile use → manual pump.
High-frequency + fixed workshop → air-hydraulic becomes more attractive.


Single-Acting vs Double-Acting Hydraulic Tools

Before choosing any pump, determine whether the hydraulic tool is:

Single Acting

or:

Double Acting

This is one of the most important compatibility checks.


What Is a Single-Acting Cylinder?

A single-acting cylinder uses hydraulic pressure to move in one direction.

Return may occur through:

Spring return

Load return

External mechanical force

It generally uses one hydraulic pressure connection.

Many portable workshop tools use this architecture.


What Is a Double-Acting Cylinder?

A double-acting cylinder uses hydraulic pressure in both directions.

One hydraulic circuit extends the piston.

Another retracts it.

This requires:

Additional hydraulic line

Suitable directional valve

Compatible pump configuration

A pump intended only for single-acting tools should not automatically be assumed to operate a double-acting cylinder correctly.


Why Valve Configuration Matters

The pump must do more than generate pressure.

It must also control:

Advance

Hold

Return

For double-acting systems:

Advance line

Return line

must be controlled correctly.

This is why pump valve configuration is a key specification.


Pressure Rating: Pump and Tool Must Match

Suppose a pump is rated to:

700 bar / 10,000 PSI

The connected components should have compatible working-pressure ratings.

That includes:

Cylinder

Hose

Gauge

Coupler

Valve

Tool head

The safest system rating is limited by the lowest-rated component.

Never select hydraulic parts independently without verifying system compatibility.


Oil Capacity: One of the Most Overlooked Pump Specifications

Many buyers focus only on pressure.

But reservoir capacity is equally important.

The pump must contain enough usable hydraulic oil to fill the cylinder during its required stroke.

A pump with insufficient usable oil capacity may reach the end of its reservoir before the cylinder completes its required movement.

This can make the pump technically pressure-compatible but practically unusable.


Why a Larger Cylinder Needs More Oil

A hydraulic cylinder contains a piston.

As the piston advances, hydraulic fluid fills the cylinder chamber.

The required volume depends mainly on:

Piston Area × Stroke

Therefore:

Larger cylinder bore

Longer stroke

generally require more hydraulic oil.

This is why pump selection should consider:

Pressure + Usable Oil Capacity

not pressure alone.


Bigger Reservoir Does Not Automatically Mean Better

A large reservoir provides more oil.

But it also makes the pump:

Larger

Heavier

Less portable

For mobile repairs, carrying several liters of unnecessary hydraulic oil adds weight without increasing useful performance.

The ideal reservoir should comfortably support the connected tool's required oil volume.


BY Manual Hydraulic Pump Sizes

BY's current hydraulic nut-splitter range includes manual hydraulic pump options such as:

400cc manual hydraulic pump

700cc heavy-duty hydraulic pump

900cc manual hydraulic pump

These different capacities illustrate an important professional buying principle:

Reservoir capacity should match the hydraulic tool and expected working stroke rather than simply choosing the largest pump available.

Different tool heads and hydraulic cylinders require different oil volumes.


What Does CC Mean on a Hydraulic Pump?

CC means cubic centimeters.

For example:

400cc

means approximately:

400 cubic centimeters of reservoir volume or specified pump oil capacity, depending on the manufacturer's specification method.

When comparing pumps, always verify whether the published figure refers to:

Total reservoir capacity

Usable oil capacity

These are not always identical.

Usable capacity is the more important value for system matching.


Flow Rate: Pressure Is Not the Same as Speed

Two pumps can both reach the same maximum pressure but move the cylinder at very different speeds.

Why?

Because:

Pressure determines potential force

while:

Oil flow determines cylinder speed

A pump delivering more oil per stroke or per minute moves the hydraulic piston faster.

This distinction is essential.


High Pressure Does Not Mean Fast Operation

A pump advertised as:

10,000 PSI

may create very high working pressure.

But that specification alone tells you nothing about how quickly it moves a cylinder.

For workflow efficiency, buyers should also check:

Oil per stroke

Oil flow per minute

One-speed vs two-speed design


How to Match a Hydraulic Pump to a Puller

For a hydraulic bearing or hub puller, check:

Maximum Working Pressure

Pump and puller cylinder must be compatible.

Required Oil Volume

Pump reservoir must support cylinder stroke.

Coupler Type

Connections must match correctly.

Hose Rating

Hose must meet or exceed system working pressure.

Cylinder Type

Single-acting or double-acting?

Control Method

Does the technician need fine manual control or faster repetitive operation?

For occasional puller use:

manual hand pump may be ideal.

For repeated professional extraction:

air-hydraulic pump may improve efficiency.


How to Match a Pump to a Hydraulic Nut Splitter

A nut splitter often requires:

Compact high-pressure pump

Controlled advance

Relatively limited cylinder travel

A manual pump can be particularly suitable because the technician can:

Build Pressure Slowly

↓

Monitor Blade Position

↓

Stop When Nut Splits

This is why compact manual pumps remain common in nut-splitting systems.


How to Match a Pump to a Hydraulic Press

A hydraulic press may require much more fluid movement than a small nut splitter.

Important factors include:

Ram bore

Ram stroke

Return method

Duty cycle

Desired operating speed

For repeated workshop press operations, manual pumping may become inefficient.

Air or electric hydraulic pumps can become more appropriate as cycle frequency increases.


How to Match a Pump to a Hydraulic Spring Compressor

Spring compression requires controlled movement.

The technician must monitor:

Spring seating

Jaw position

Compression symmetry

Tool alignment

A manual or foot-controlled hydraulic system can provide useful gradual control.

For high-volume suspension service, powered hydraulic systems may reduce operator effort.

Safety remains dependent on the complete spring-compressor structure-not just the pump.


How to Match a Pump to a Hydraulic Hub Puller

Hub pullers may require high sustained pressure when corrosion is severe.

A compact manual pump offers:

Portability

Controlled pressure increase

An air-hydraulic pump offers:

Lower operator effort

Faster repetitive use

The better option depends on:

Repair Frequency + Required Oil Volume + Workshop Power Source


Hose Compatibility Matters

The hose connects the pump to the tool.

It carries full hydraulic pressure.

Professional systems should verify:

Working-pressure rating

Hose condition

Length

End fittings

Bend condition

Protection from abrasion

Do not treat hydraulic hose as an ordinary flexible tube.

A damaged high-pressure hose should be removed from service.


Couplers Are Part of the Pressure System

Quick couplers make hydraulic tools easier to change.

But couplers also carry the system pressure.

Check:

Pressure rating

Thread type

Connection size

Male/female compatibility

Locking engagement

A coupler that looks similar is not necessarily hydraulically compatible.


Why a Pressure Gauge Is Useful

A gauge allows the technician to monitor hydraulic pressure.

Without a gauge, the operator may know that the tool is working but not know the actual system pressure.

A pressure gauge can help with:

Monitoring load

Repeating procedures

Diagnosing unusual resistance

Avoiding unnecessary pressure escalation

However, pressure should still be interpreted together with cylinder specifications.


Pressure Is Not Directly Equal to Tonnage

This distinction is worth repeating.

A gauge may show:

700 bar

But cylinder force depends on piston area.

A small cylinder at 700 bar generates less force than a large cylinder at the same pressure.

Therefore:

PSI / bar describes hydraulic pressure. Tons describe resulting force at a particular cylinder.

Do not use these terms interchangeably.


When Is a Manual Hand Pump the Best Choice?

Choose a manual hand pump when:

Tool use is occasional

Portability matters

No compressed air is available

Slow controlled movement is preferred

Tool oil volume is relatively modest

Simple maintenance is important

Typical applications:

Nut splitters

Portable pullers

Small cylinders

Field repairs


When Is a Foot Pump the Better Choice?

Choose a foot-controlled pump when:

Hands need to stay free

Technician needs to stabilize the workpiece

Tool positioning must be monitored continuously

Then determine whether you need:

Manual Foot Power

or:

Air-Hydraulic Foot Control

based on duty cycle and available compressed air.


When Is an Air-Hydraulic Pump the Better Choice?

Choose air-hydraulic when:

Shop air is readily available

Hydraulic tools are used frequently

Operator fatigue needs to be reduced

Faster repeat cycles are valuable

Hands-free foot control is useful

Professional workshop use is where air-hydraulic pumps often provide the strongest productivity advantage.


Manual vs Foot vs Air-Hydraulic: Workshop Decision Matrix

Workshop Situation Hand Pump Manual Foot Pump Air-Hydraulic
Mobile mechanic Excellent Excellent Limited
Small garage Excellent Very good Optional
Occasional hydraulic work Excellent Good Usually unnecessary
Repetitive daily work Moderate Moderate Excellent
Need both hands free Limited Excellent Excellent
No electricity Excellent Excellent Excellent if air available
No compressed air Excellent Excellent No
High portability Excellent Excellent Moderate
Lower operator fatigue Moderate Moderate Excellent
Simple maintenance Excellent Excellent More complex

Common Mistake 1: Choosing Only by Maximum Pressure

Pressure does not tell you:

Oil capacity

Flow rate

Cylinder speed

Control method

Valve compatibility

Check the entire system.


Common Mistake 2: Assuming Every 10,000 PSI Pump Is Interchangeable

Two pumps may share the same pressure rating but differ in:

Reservoir capacity

Flow

Valve design

Single/double-acting compatibility

Couplers

Pressure compatibility alone is insufficient.


Common Mistake 3: Ignoring Oil Capacity

A pump can reach the correct pressure but still be unable to fully extend the cylinder.

Check usable oil volume.


Common Mistake 4: Connecting a Single-Acting Pump to a Double-Acting Tool Without Checking Valve Design

A double-acting cylinder needs controlled hydraulic flow in both directions.

Use the correct pump and valve arrangement.


Common Mistake 5: Using the Wrong Hose or Coupler

High-pressure components must match the system rating.

Never improvise with lower-rated hoses or fittings.


Common Mistake 6: Thinking a Foot Pump Is Always Air-Powered

Some foot pumps are manual.

Some are air-over-hydraulic.

Check the actual power source.


Common Mistake 7: Choosing the Largest Reservoir Automatically

More oil means more weight.

Match capacity to the tool.


Common Mistake 8: Ignoring Duty Cycle

A manual pump may be perfect for one nut splitter operation per week.

It may become inefficient for dozens of repetitive hydraulic cycles every day.

Tool frequency changes the best pump choice.


Common Mistake 9: Confusing Hydraulic Pressure With Output Force

The pump supplies pressure.

The cylinder converts that pressure into force.

Always evaluate the pump and cylinder as a system.


Common Mistake 10: Buying the Pump Separately Without Checking the Complete Hydraulic Circuit

Professional hydraulic systems include:

Pump

Valve

Hose

Coupler

Gauge

Cylinder / Tool

All components should be compatible.


What Should Professional Buyers Check?

For workshop and B2B purchasing, evaluate:

Maximum Working Pressure

Does it match the hydraulic tool?

Usable Oil Capacity

Can it fully operate the cylinder?

Flow Rate

How quickly will the tool move?

Single- or Double-Acting Compatibility

Does the valve configuration match?

Power Source

Manual, air, electric or battery?

Operator Control

Hand, foot, pendant or valve?

Hose Connection

What port and coupler are required?

Pressure Gauge Compatibility

Can pressure be monitored?

Reservoir Construction

Steel, aluminum, reinforced polymer or another design?

Replacement Parts

Can seals, hoses, couplers and valves be serviced?


What Makes a Professional Hydraulic Pump?

A professional pump should not be judged only by pressure.

A better evaluation is:

Pressure + Flow + Oil Capacity + Valve Control + Compatibility + Durability + Serviceability

For frequent workshop use, repeatability matters.

The pump should provide predictable operation across repeated service cycles.


BY Hydraulic Pump Solutions for Automotive Workshop Tools

BY / Baiyu Tools supplies hydraulic automotive tools for workshops, distributors, wholesalers and private-label customers.

BY's current product range includes manual hydraulic pumps paired with tools such as hydraulic nut splitters, with available pump capacities including:

400cc

700cc

900cc

These products illustrate how pump selection can vary according to the hydraulic tool and required oil capacity.

BY's broader hydraulic automotive tool range also includes applications involving:

Bearing removal

Hub pulling

Nut splitting

Suspension service

Pressing and extraction

For B2B buyers, hydraulic tool programs can also be configured around:

Pump Capacity

Hose

Coupler

Hydraulic Tool Head

Packaging

OEM / Private Label Requirements

The important purchasing principle is:

Do not select the hydraulic pump separately from the tool it must operate. Treat the pump, hose, coupler and cylinder as one hydraulic system.


Frequently Asked Questions

What are the main types of hydraulic pumps used with workshop tools?

Common portable workshop types include manual hand pumps, manual foot pumps and air-hydraulic pumps. Electric and battery-powered pumps are also used in higher-duty applications.

Is a foot pump the same as an air-hydraulic pump?

No. A foot pump describes how the pump is controlled. A foot-operated pump may be manually powered or it may use compressed air to generate hydraulic pressure.

What is an air-hydraulic pump?

An air-hydraulic pump uses compressed air to drive a hydraulic pumping mechanism, creating high-pressure hydraulic fluid for cylinders and tools.

Is a manual hydraulic pump suitable for a puller?

Yes, provided its pressure, oil capacity, valve design, hose and coupler are compatible with the puller cylinder.

What does 10,000 PSI mean on a hydraulic pump?

It means the pump is designed to operate up to the specified hydraulic pressure. It does not mean the pump itself produces a fixed tonnage because cylinder piston area determines output force.

Is 700 bar the same as 10,000 PSI?

They are approximately equivalent pressure ratings commonly used in high-pressure portable hydraulic tool systems.

How do I know what hydraulic pump I need for a cylinder?

Check the cylinder's maximum pressure, oil-volume requirement, single- or double-acting design, connection type and desired operating speed.

Why does reservoir capacity matter?

The reservoir must contain enough usable oil to move the hydraulic cylinder through its required stroke.

Is a larger hydraulic reservoir better?

Not automatically. A larger reservoir provides more oil but also increases pump size and weight. Match capacity to the connected tool.

What is the difference between single-acting and double-acting hydraulic pumps?

A pump configured for single-acting tools typically pressurizes one hydraulic line. Double-acting tools require a valve and circuit capable of controlling pressure for both extension and retraction.

Which pump is best for a professional workshop?

For occasional or mobile work, a manual hand or foot pump is often practical. For frequent repetitive operation in a workshop with compressed air, an air-hydraulic pump can reduce operator effort and improve productivity.

Can the same hydraulic pump power a nut splitter and a puller?

Potentially, but only if the pressure rating, usable oil capacity, valve configuration, hoses, couplers and tool requirements are compatible.


Conclusion

Choosing a hydraulic pump for workshop tools should not begin with:

Hand or Foot?

or:

How many PSI?

The correct starting point is the tool being powered.

First determine:

What hydraulic tool will the pump operate?

Then check:

Single Acting or Double Acting

↓

Required Pressure

↓

Required Oil Volume

↓

Flow / Desired Operating Speed

↓

Hose and Coupler Compatibility

Only after those technical requirements are established should the workshop choose the preferred power and control method.

For portable and occasional work:

Manual Hand Pump

offers simplicity and independence.

When hands-free manual operation is useful:

Manual Foot Pump

can improve ergonomics.

For repetitive workshop use where compressed air is available:

Air-Hydraulic Pump

can significantly reduce technician effort.

And this leads to the most important distinction:

Hand and foot describe how the technician operates the pump. Manual, air, electric and battery describe how the hydraulic power is generated.

A professional workshop should therefore select a pump as part of a complete hydraulic system:

Pump + Valve + Hose + Coupler + Gauge + Cylinder / Tool

When those components are correctly matched, hydraulic power becomes one of the most versatile force sources in the automotive workshop.

Send Inquiry

Home

Phone

E-mail

Inquiry