Nov 12, 2026 Leave a message

How To Match A Hydraulic Pump To A Cylinder: Pressure, Tonnage And Oil Capacity Explained

Choosing a hydraulic pump for a cylinder can look simple.

The cylinder says:

10 ton.

The pump says:

10,000 PSI.

So they should work together-right?

Not necessarily.

Pressure and tonnage are only part of the matching process.

A hydraulic pump can have enough pressure to operate a cylinder but still be unsuitable because:

  • Its usable oil capacity is too small
  • Its oil flow is too low
  • The valve does not match the cylinder type
  • The hose or coupler is incompatible
  • The cylinder requires more stroke volume than the pump can supply
  • The complete hydraulic system has a lower-rated component

The correct way to match a hydraulic pump to a cylinder is:

Cylinder → Required Force → Working Pressure → Oil Volume → Flow → Single/Double Acting → Hose and Coupler → Pump Type

The key principle is:

The pump supplies pressure and oil flow. The cylinder converts that pressure into mechanical force.

Once that distinction is clear, pump-to-cylinder selection becomes much easier.

Quick Answer: How Do You Match a Hydraulic Pump to a Cylinder?

Check these specifications in order:

Parameter What You Need to Match
Cylinder Capacity Required force for the job
Cylinder Maximum Pressure Pump pressure must remain within cylinder rating
Effective Piston Area Determines force at a given pressure
Cylinder Stroke Determines required travel
Cylinder Oil Capacity Pump must supply enough usable oil
Pump Flow / Displacement Determines cylinder operating speed
Cylinder Type Single-acting or double-acting
Valve Configuration Must correctly control the cylinder
Hose and Coupler Pressure and connection must be compatible
Gauge Should suit the system pressure range

A useful professional rule is:

Do not select the pump from cylinder tonnage alone.

1. Understand What the Pump Does and What the Cylinder Does

A hydraulic system normally includes:

Pump → Valve → Gauge → Hose → Coupler → Cylinder → Mechanical Tool

Each component performs a different job.

The Hydraulic Pump

The pump:

  • moves hydraulic oil;
  • creates oil flow;
  • allows pressure to develop when the system meets resistance.

The Hydraulic Cylinder

The cylinder:

  • receives pressurized hydraulic oil;
  • converts hydraulic pressure into linear mechanical force;
  • moves through a defined stroke.

Therefore:

A pump does not directly "produce 10 tons." The cylinder produces force according to the pressure applied to its effective piston area.

2. Pressure vs Tonnage: What Is the Difference?

This is the most important concept when matching a pump to a cylinder.

Pressure

Hydraulic pressure is normally measured in:

PSI

or:

bar.

Pressure describes how much hydraulic force exists per unit area.

Tonnage

Tonnage describes the mechanical force generated by the hydraulic cylinder.

The simplified relationship is:

Force = Hydraulic Pressure × Cylinder Effective Area

Therefore:

Pressure ≠ Tonnage

The cylinder piston area connects the two.

3. Why the Same Pump Can Operate Different-Tonnage Cylinders

Imagine a hydraulic pump capable of supplying the same working pressure to two cylinders.

Cylinder A has a relatively small piston area.

Cylinder B has a much larger piston area.

At the same hydraulic pressure:

Cylinder B produces more force.

The pump did not become stronger.

The difference comes from cylinder geometry.

This explains why the same compatible pump may potentially operate:

5-ton, 10-ton, 20-ton or larger cylinders

provided the pressure, oil-volume, valve and connection requirements all match.

4. How Much Pressure Does a Hydraulic Cylinder Need?

If you know the required force and cylinder effective area, the required hydraulic pressure can be calculated as:

Pressure = Required Force ÷ Effective Piston Area

This is why professional cylinder specifications should ideally provide:

  • Rated capacity
  • Maximum working pressure
  • Effective piston area
  • Stroke
  • Oil capacity

Do not assume that a cylinder must always operate at maximum pump pressure.

If the load can be moved at lower pressure, the system only needs to develop the pressure required to overcome that load.

5. Does a 10-Ton Cylinder Always Need 10,000 PSI?

No.

This is a common misunderstanding.

A cylinder's rated tonnage is related to:

working pressure × effective piston area.

If the actual load is lower than the cylinder's rated capacity, it may require substantially less than maximum hydraulic pressure.

For example:

A cylinder rated for approximately 10 tons at its maximum designed pressure does not automatically operate at maximum pressure during every job.

The pressure rises according to resistance.

This is why a gauge is useful.

6. What Does 10,000 PSI / 700 Bar Mean?

Many portable professional hydraulic tools operate in approximately the:

10,000 PSI / 700 bar pressure class.

This pressure class is commonly found in:

  • Hydraulic pullers
  • Portable cylinders
  • Nut splitters
  • Pressing tools
  • Industrial maintenance equipment

But 10,000 PSI does not tell you:

  • Cylinder tonnage
  • Cylinder stroke
  • Pump reservoir capacity
  • Pump speed
  • Oil flow

It only describes the hydraulic pressure capability.

7. Never Use a Higher-Pressure Pump to "Make the Cylinder Stronger"

If a cylinder is rated for a particular maximum working pressure, do not exceed it simply because a higher-pressure pump is available.

The same applies to:

  • Hoses
  • Couplers
  • Gauges
  • Valves
  • Adapters

The safe pressure of the complete hydraulic system is limited by its lowest-rated pressure-bearing component.

A higher-pressure pump does not upgrade the pressure rating of the cylinder or hydraulic accessories.

8. Cylinder Tonnage Is Not Enough to Select a Pump

Consider two cylinders:

Cylinder A

10-ton capacity + short stroke

Cylinder B

10-ton capacity + long stroke

They may have similar force capacity.

But Cylinder B requires substantially more hydraulic oil to reach full extension.

Therefore they may need different pump reservoir capacities.

This leads to the second major pump-selection factor:

oil capacity.

9. How Much Oil Does a Hydraulic Cylinder Need?

The approximate oil requirement of a cylinder is calculated from:

Cylinder Oil Capacity = Effective Piston Area × Stroke

This means:

Larger piston area → more oil required

and:

Longer stroke → more oil required.

This is why cylinder stroke is essential when choosing a pump.

10. Example: Same Tonnage, Different Stroke

Imagine two cylinders with the same piston area.

Cylinder A has:

50 mm stroke

Cylinder B has:

150 mm stroke.

Assuming identical effective areas:

Cylinder B requires approximately three times as much oil for full extension.

Both cylinders may produce the same rated force.

But their pump oil-volume requirements are very different.

11. Pump Usable Oil Capacity Must Match Cylinder Oil Requirement

Once the cylinder's required oil volume is known, compare it with:

pump usable oil capacity.

The pump must contain enough deliverable hydraulic oil to:

  • extend the cylinder through the required stroke;
  • fill the hydraulic hose;
  • support any additional hydraulic components in the circuit.

A practical rule is:

Pump Usable Oil Capacity > Cylinder Oil Requirement + Hydraulic Circuit Oil Requirement

A small additional capacity margin is preferable to selecting a reservoir that only just equals the theoretical cylinder volume.

12. Why the Hose Also Consumes Hydraulic Oil

The hose contains hydraulic fluid.

A longer or larger internal-diameter hose holds more oil.

In a small compact cylinder system, hose volume may be relatively minor.

In longer hydraulic circuits or multi-cylinder systems, it becomes more important.

Therefore the correct matching process considers:

Cylinder Oil + Hose Oil + Other Hydraulic Circuit Volume

rather than cylinder capacity alone.

13. Total Reservoir Capacity vs Usable Oil Capacity

These are not always the same specification.

Total Reservoir Capacity

How much oil the reservoir can physically contain.

Usable Oil Capacity

How much hydraulic oil can actually be supplied to the working circuit under specified operating conditions.

When matching a pump to a cylinder:

usable oil capacity is generally the more important number.

14. What Happens if the Pump Reservoir Is Too Small?

A pump can have:

the correct pressure

but:

insufficient oil capacity.

The result may be:

  • Cylinder cannot reach full stroke
  • Pump begins drawing air
  • Operation becomes irregular
  • System cannot complete the job

This is an incorrectly matched hydraulic system even if the pressure specification looks correct.

15. What Happens if the Pump Reservoir Is Much Larger Than Necessary?

Usually the system can still operate if all other specifications are compatible.

However, unnecessarily large reservoirs can make a hand pump:

  • Heavier
  • Larger
  • Harder to transport
  • More expensive

For portable automotive tools, this matters.

The objective should be:

enough usable oil capacity-not simply the largest pump available.

16. 400cc vs 700cc vs 900cc: What Do These Numbers Mean?

BY currently lists hydraulic nut-splitter systems with manual hydraulic pump configurations including:

400cc

700cc

and:

900cc.

These products can be found in the BY Hydraulic Nut Splitter and Nut Extractor Tools range.

The important point is:

400cc, 700cc and 900cc primarily describe oil-volume capacity. They should not automatically be interpreted as low, medium and high hydraulic force.

Do not confuse:

700cc = oil volume

with:

700 bar = hydraulic pressure.

They describe completely different specifications.

17. Flow Determines Cylinder Speed

Once pressure and oil capacity are correct, the next question is:

How quickly will the cylinder move?

Cylinder speed depends primarily on hydraulic flow relative to the effective cylinder area.

In simplified form:

Higher Pump Flow → Faster Cylinder Movement

while:

Larger Cylinder Area → More Oil Required for the Same Travel Speed

This is why a very large cylinder can feel extremely slow when connected to a small hand pump.

18. A Pump Can Have Enough Pressure but Still Be Too Slow

Suppose a hand pump reaches:

700 bar.

It may have more than enough pressure to operate the cylinder.

But if it delivers only a relatively small amount of oil per handle stroke:

the technician may need many strokes to extend the cylinder.

The hydraulic system is technically compatible.

But the workshop workflow may be inefficient.

19. Oil Displacement Per Stroke Matters for Hand Pumps

For manual hydraulic pumps, check:

oil displacement per stroke.

A higher displacement moves more oil each time the technician operates the handle.

That reduces the number of strokes required to move the cylinder.

This becomes increasingly important for:

  • Large cylinders
  • Long strokes
  • Frequent workshop use

20. Why Two-Speed Pumps Work Well With Larger Cylinders

A two-speed manual hydraulic pump normally provides:

Low-Pressure Stage

Higher oil volume per stroke.

This quickly moves the cylinder toward the workpiece.

High-Pressure Stage

Lower oil volume but higher pressure capability.

This provides the force once the cylinder contacts the load.

The operating sequence is therefore:

Fast Approach → Contact → High-Pressure Work

This can significantly reduce unnecessary handle strokes when operating larger hydraulic pullers and cylinders.

21. Match the Pump to Single-Acting or Double-Acting Cylinders

Pressure and reservoir capacity are still not enough.

You also need to know whether the cylinder is:

Single Acting

or:

Double Acting.

Single-Acting Cylinder

Hydraulic pressure normally moves the piston in one direction.

The cylinder returns using:

  • Spring force
  • Load force
  • Gravity

A typical portable single-acting hydraulic circuit requires:

Pump → One Hydraulic Hose → Cylinder

Double-Acting Cylinder

Hydraulic pressure controls:

Advance

and:

Retract.

This normally requires:

  • Two hydraulic ports
  • Two hoses
  • A compatible directional valve

A pump can have enough pressure and oil capacity but still be incompatible if its valve is wrong.

22. Pressure Matching Alone Does Not Guarantee Compatibility

Consider:

Pump: 700 bar

Cylinder: 700 bar

At first glance, they appear compatible.

But the cylinder is double-acting.

The pump only has a simple release valve intended for a single-acting tool.

The combination is therefore not a correct hydraulic control system.

This gives another important rule:

Pressure compatibility does not automatically mean system compatibility.

23. Match the Hydraulic Hose

The hydraulic hose must match:

  • Maximum working pressure
  • Pump outlet
  • Cylinder connection
  • Coupler type
  • Required working length

Never choose a hose only because:

"the fitting screws in."

Physical fit does not prove:

pressure compatibility.

24. Match the Quick Couplers

Hydraulic quick couplers must match:

  • Pressure rating
  • Male/female design
  • Connection size
  • Thread type
  • Internal valve arrangement

A coupler that is not fully engaged can prevent oil from flowing correctly.

The pump may then build pressure while the cylinder barely moves-or does not move at all.

25. Use a Pressure Gauge

A gauge gives the technician a direct view of hydraulic system pressure.

This is useful because it helps distinguish:

Low Pressure

from:

High Pressure but No Movement.

These are very different problems.

If pressure remains low:

investigate the pump, valve, oil level and leaks.

If pressure reaches a high level but the cylinder does not move:

investigate:

  • Load
  • Coupler
  • Mechanical blockage
  • Cylinder capacity
  • Tool setup

26. Pump + Cylinder + Gauge + Hose Should Be Treated as One System

BY's Hydraulic Bearing Puller Range is a good practical example.

The hydraulic section of these puller systems can include:

  • Hydraulic cylinder
  • Pump
  • Hydraulic hose
  • Pressure gauge
  • Gauge adaptor
  • Coupling

The mechanical section then transfers the resulting cylinder force into the component being removed.

This is why professional hydraulic tools should be sold and specified as:

a complete load system rather than a collection of unrelated components.

27. Matching a Pump to a Hydraulic Bearing Puller

Hydraulic bearing pullers typically require:

  • High controlled pressure
  • Moderate cylinder stroke
  • Reliable couplers
  • Correct gauge range
  • A pump with enough usable oil

BY's Bearing Puller and Gear Puller Range includes mechanical and hydraulic pulling solutions for bearings, gears and pulleys.

The dedicated BY Hydraulic Bearing Pullers currently cover multiple pulling capacities.

When selecting the pump, first identify the hydraulic cylinder supplied with the puller.

Then match:

Pressure + Oil Volume + Hose + Coupler + Gauge.

28. Matching a Pump to a Hydraulic Hub Puller

Wheel hub pulling can require substantial sustained axial force when corrosion or tight fit increases removal resistance.

BY's 10 Ton Hydraulic Wheel Hub Puller With Hammer Set uses a hydraulic spindle rated at 10 tons together with mechanical and impact removal methods.

This demonstrates an important point:

10 ton

describes the stated force capacity of the hydraulic component.

It does not describe:

pump reservoir capacity.

And it does not mean:

10,000 PSI.

Tonnage, pressure and oil volume remain separate specifications.

29. Matching a Pump to a Hydraulic Nut Splitter

Hydraulic nut splitters usually have relatively short cylinder travel.

This means they may require:

high pressure

but comparatively:

low oil volume.

That is one reason compact manual pumps are practical for this application.

See the BY Hydraulic Nut Splitter and Nut Extractor Range for examples of different pump and cutting-head configurations.

30. Matching a Pump to a Workshop Press Cylinder

A workshop press can present the opposite situation.

The cylinder may have:

  • Larger piston area
  • Longer stroke
  • Higher oil-volume requirement

A small manual pump may technically reach the required pressure.

But the technician may need an excessive number of handle strokes.

For occasional use:

manual operation may still be practical.

For repetitive work:

higher-flow air or electric pumps may become more efficient.

31. Larger Cylinder = Larger Pump?

Not always in terms of pressure.

A larger cylinder can generate more force at the same hydraulic pressure.

But larger cylinders normally require more oil.

Therefore larger cylinders tend to increase:

oil-volume and flow requirements

more directly than:

maximum pressure requirements.

32. Why Large Cylinders Are Often Paired With Powered Pumps

A manual pump can potentially operate a large compatible cylinder.

The problem is productivity.

If the cylinder requires a very large volume of hydraulic oil:

hundreds of manual handle strokes may be impractical.

At that point an:

air-hydraulic pump

or:

electric hydraulic pump

may provide a much better workshop workflow.

33. What About Multiple Cylinders?

If one pump operates multiple cylinders, the total oil requirement increases.

For example:

4 cylinders × individual cylinder oil capacity

must be considered.

The pump also needs enough oil for:

  • Hoses
  • Manifolds
  • Valves

Multi-cylinder systems introduce another issue:

cylinders do not necessarily move at exactly the same speed simply because they are connected to the same pump.

Load distribution and hydraulic control also matter.

34. Pump Pressure Does Not Guarantee Puller Capacity

This is particularly important with hydraulic pullers.

The hydraulic cylinder may be capable of very high force.

But the complete system also contains:

  • Puller body
  • Jaws
  • Crosshead
  • Bolts
  • Adapters

The complete tool must be rated for the hydraulic load.

Never use more hydraulic pressure simply because the component will not move.

Hydraulic force can magnify an incorrect mechanical setup.

35. Required Force Should Be Below Maximum Tool Capacity

Professional workshops should avoid selecting a cylinder that must operate at its absolute limit on every job.

Suitable capacity margin improves:

  • Tool life
  • Control
  • Safety
  • Application flexibility

The exact margin should follow the equipment manufacturer's application and safety recommendations.

Do not create an arbitrary tonnage margin that conflicts with the tool documentation.

36. Common Mistake: "My Cylinder Is 10 Ton, So I Need a 10-Ton Pump"

This terminology is incorrect.

The pump is normally specified by:

  • Maximum pressure
  • Oil capacity
  • Flow
  • Valve configuration

The cylinder is specified by:

  • Force capacity
  • Pressure rating
  • Effective area
  • Stroke
  • Oil capacity

Match the specifications rather than trying to match a "pump tonnage."

37. Common Mistake: "10,000 PSI Means 10 Tons"

No.

10,000 PSI is pressure.

10 tons is force.

The cylinder piston area determines the relationship between them.

38. Common Mistake: Choosing Only by Maximum Pressure

A pump may have the correct pressure while having:

  • Insufficient oil capacity
  • Insufficient flow
  • Wrong valve configuration
  • Wrong couplers

Pressure is only the first compatibility check.

39. Common Mistake: Choosing Only by Reservoir Size

A 900cc pump is not automatically more powerful than a 400cc pump.

Reservoir capacity primarily determines:

how much oil is available.

It does not directly determine:

maximum cylinder force.

40. Common Mistake: Ignoring Stroke

Cylinder stroke directly changes oil demand.

Two cylinders with the same tonnage but different strokes can require very different pump capacities.

41. Common Mistake: Ignoring Flow

A low-flow pump can be fully pressure-compatible while still being painfully slow.

This matters especially in professional workshops where technician time matters.

42. Common Mistake: Ignoring Valve Configuration

A single-acting cylinder and double-acting cylinder require different hydraulic control strategies.

Never assume that matching pressure alone is sufficient.

43. Common Mistake: Assuming All Couplers Are Universal

Hydraulic couplers may differ in:

  • Size
  • Thread
  • Valve geometry
  • Pressure rating
  • Manufacturer interface

A physically similar coupler is not automatically compatible.

44. Professional Pump-to-Cylinder Matching Checklist

Parameter Cylinder / Tool Pump / System
Required Force ___ ton / kN Suitable cylinder selected
Maximum Pressure ___ bar / PSI ___ bar / PSI
Effective Area ___ cm² / in² Used for force calculation
Stroke ___ mm / in -
Cylinder Oil Capacity ___ cc -
Pump Usable Oil Required > total system demand ___ cc
Flow / Displacement Required operating speed ___ cc/stroke or L/min
Acting Type Single / Double Compatible valve
Hose Pressure / connection Compatible
Coupler Type / thread Compatible
Gauge Required range Compatible
Duty Cycle Occasional / Frequent Manual / Air / Electric

45. What Should B2B Buyers Ask a Hydraulic Tool Supplier?

Professional distributors should request measurable data.

Ask:

  • What is the cylinder's rated capacity?
  • At what pressure is that capacity achieved?
  • What is the cylinder effective piston area?
  • What is the cylinder stroke?
  • What is the cylinder oil capacity?
  • What is the pump usable oil capacity?
  • What is the pump flow or displacement per stroke?
  • Is the cylinder single-acting or double-acting?
  • What valve configuration is required?
  • What hose pressure rating is used?
  • What coupler specification is used?
  • Can a pressure gauge be installed?
  • Which pump and cylinder combinations have been tested together?

This creates far more purchasing value than asking:

"How many tons is the hydraulic pump?"

46. Why Complete Hydraulic Kits Are Easier to Specify

For many workshops, purchasing a properly matched system reduces uncertainty.

A professionally configured kit can include:

Pump + Cylinder + Hose + Coupler + Gauge + Mechanical Tool

This reduces the risk of:

  • Pressure mismatch
  • Insufficient pump oil capacity
  • Wrong couplers
  • Wrong hose specification
  • Incorrect valve selection

BY's Professional Hydraulic Bearing Puller Systems show this complete-system approach.

47. BY Hydraulic Tool Applications

BY / Baiyu Tools develops automotive specialty tools for workshops, wholesalers, distributors and private-label programs.

Relevant hydraulic applications include:

Hydraulic Bearing Pullers

Bearing Puller and Gear Puller Tools

10 Ton Hydraulic Wheel Hub Puller With Hammer Set

Hydraulic Nut Splitter and Nut Extractor Tools

The correct OEM/ODM approach is not to choose these components independently.

Instead, define:

Required Force + Cylinder Geometry + Pressure + Stroke + Oil Volume + Flow + Hose + Coupler + Workshop Duty Cycle

Frequently Asked Questions

How do I match a hydraulic pump to a cylinder?

Check the cylinder's maximum pressure, rated force, effective piston area, stroke, oil capacity and single- or double-acting design. Then choose a pump with compatible pressure, enough usable oil, suitable flow, the correct valve configuration, and compatible hoses and couplers.

Does a 10-ton hydraulic cylinder need a 10-ton hydraulic pump?

No. Pumps are primarily specified by pressure, oil capacity, flow and valve configuration. Cylinder tonnage results from hydraulic pressure acting on the cylinder's effective piston area.

Does a 10-ton cylinder require 10,000 PSI?

Not necessarily during every operation. The pressure required depends on the actual load and the cylinder's effective piston area. Never exceed the cylinder's rated maximum pressure.

Can a 10,000 PSI pump operate a 20-ton cylinder?

Potentially, if the cylinder is designed for that pressure and the pump provides enough usable oil, suitable flow, the correct valve, and compatible hoses and couplers.

Can the same hydraulic pump operate 5-ton and 10-ton cylinders?

Potentially yes. The cylinders can produce different forces at the same pressure because they have different effective piston areas. All other hydraulic specifications must also match.

How much oil does my hydraulic cylinder need?

Cylinder oil capacity is approximately equal to effective piston area multiplied by stroke. Use the manufacturer's published oil-capacity specification whenever available.

How much pump oil capacity do I need?

The pump's usable oil capacity should exceed the total oil requirement of the cylinder and associated hydraulic circuit, including hoses and other connected components.

Is a larger hydraulic pump reservoir better?

Not automatically. A larger reservoir provides more oil but also increases pump size and weight. Choose enough usable oil for the connected cylinder and circuit.

Why is my hydraulic cylinder moving very slowly?

If pressure and connections are correct, the pump may have insufficient flow for the cylinder's effective area and stroke. A larger cylinder requires more oil for a given travel distance.

Does more pump pressure make the cylinder move faster?

No. Pressure primarily determines available force. Oil flow primarily determines cylinder speed.

What is more important: pump pressure or oil capacity?

Both are essential. Pressure must be sufficient and compatible with the cylinder, while usable oil capacity must be sufficient to complete the required cylinder stroke.

Can I use a small hand pump with a large cylinder?

Potentially, if pressure, oil capacity and valve requirements are compatible. However, operation may be very slow because the technician must manually move a large volume of oil.

Why are two-speed pumps useful with large cylinders?

They provide higher oil displacement during low-pressure approach and switch to lower-flow, high-pressure operation once the load is engaged, reducing unnecessary handle strokes.

Can a single-acting pump operate a double-acting cylinder?

A basic single-acting valve circuit cannot correctly control a double-acting cylinder. A compatible directional valve and appropriate two-line hydraulic circuit are required.

Does hose volume matter when selecting a pump?

Yes. Hydraulic hoses contain oil, so total system oil requirement includes both cylinder volume and the connected hydraulic circuit.

Should I use a pressure gauge?

For professional hydraulic work, a correctly rated gauge is useful for monitoring system pressure, diagnosing resistance and preventing unnecessary pressure escalation.

Why does my pump reach high pressure but the cylinder still does not move?

The load may exceed cylinder capacity, a coupler or hose may restrict flow, or the mechanical tool may be incorrectly configured. High gauge pressure indicates that the pump may already be generating hydraulic pressure.

Conclusion

Matching a hydraulic pump to a cylinder requires more than matching one pressure number.

The correct process begins with the cylinder and the job.

First determine:

Required Mechanical Force

↓

Cylinder Capacity and Effective Area

↓

Required / Maximum Working Pressure

↓

Cylinder Stroke

↓

Cylinder Oil Capacity

↓

Pump Usable Oil Capacity

↓

Pump Flow / Displacement

↓

Single- or Double-Acting Valve Configuration

↓

Hose + Coupler + Gauge Compatibility

The three most important relationships are:

Force = Pressure × Effective Piston Area

Cylinder Oil Capacity = Effective Piston Area × Stroke

Pump Usable Oil Capacity Must Be Greater Than the Oil Required by the Cylinder and Hydraulic Circuit

This explains why:

a 10,000 PSI pump does not automatically mean 10 tons;

a 900cc pump is not automatically stronger than a 400cc pump;

and:

a pump with enough pressure can still be completely wrong for the cylinder.

For portable pullers and short-stroke nut splitters, a compact manual pump may provide an efficient solution.

For larger or long-stroke cylinders, usable oil volume and pump flow become increasingly important.

For high-cycle professional workshops, air or electric pumps may provide better productivity.

The best hydraulic pump is therefore not the pump with the highest pressure, largest reservoir or largest number on the label.

It is:

the pump whose pressure, oil capacity, flow, valve, hose and coupler are correctly matched to the cylinder and the actual workshop application.

 

Send Inquiry

Home

Phone

E-mail

Inquiry